Use this US ring size chart to translate inside diameter or inside circumference into an approximate ring size. A 17.3 mm inside diameter is around US 7. A 59.5 mm inside circumference is around US 9. Read the column for the measurement you actually took.
US Ring Size Chart in Millimeters
Got a ring that fits? Measure straight across the center, from one inside edge to the other, then use the diameter column. Starting with a strip of paper around your finger? Mark where the ends meet, lay it flat and use that length in the circumference column.
| US size | Inside diameter (mm) | Inside circumference (mm) |
|---|---|---|
| 3 | 14.1 | 44.2 |
| 3.5 | 14.5 | 45.5 |
| 4 | 14.9 | 46.8 |
| 4.5 | 15.3 | 48.0 |
| 5 | 15.7 | 49.3 |
| 5.5 | 16.1 | 50.6 |
| 6 | 16.5 | 51.9 |
| 6.5 | 16.9 | 53.1 |
| 7 | 17.3 | 54.4 |
| 7.5 | 17.7 | 55.7 |
| 8 | 18.1 | 57.0 |
| 8.5 | 18.6 | 58.3 |
| 9 | 18.9 | 59.5 |
| 9.5 | 19.4 | 60.8 |
| 10 | 19.8 | 62.1 |
| 10.5 | 20.2 | 63.4 |
| 11 | 20.6 | 64.6 |
| 11.5 | 21.0 | 65.9 |
| 12 | 21.4 | 67.2 |
| 12.5 | 21.8 | 68.5 |
| 13 | 22.2 | 69.7 |
These are reference sizes. The approximate diameters are calculated from the circumference values and rounded to one decimal place. Check the ring’s own size chart where available, especially when comparing brands or a particular band shape. The Tiffany sizing guide provides the reference circumference series, and the GIA ring sizing guide explains additional variables that affect fit.
How to Read the Chart
- Existing ring. Measure inside edge to inside edge across the center of the opening. An inside diameter of around 19.8 mm is close to US 10.
- Paper strip around the finger. Read the entire length around the finger in the circumference column. Around 54 mm is close to US 7 on this reference chart. Confirm the label on the seller’s sizing system if the listing says “54.”
A millimeter figure is meaningful only with its measurement type. A diameter goes across the opening. A circumference goes around it. Check the tool, measurement column, and intended finger again if two methods return different sizes. The at-home measuring guide shows each method.
Ring Size Chart FAQs
How big is a US size 9 ring?
A US 9 ring is approximately 18.9 mm across the inside opening, or about 59.5 mm around the inside.
How big is a US size 10 ring?
A US 10 ring is approximately 19.8 mm in inside diameter and 62.1 mm in inside circumference. For tape marked in inches, 19.8 mm is about 0.78 inches across.
What if my ring measurement falls between sizes?
Say your ring measures 17.5 mm across the inside. That falls between US 7 and 7.5 on this chart. Measure once more and check the chart for the band you’re buying. If it’s a wide band or your knuckle is wider than the base of your finger, try the two sizes in a band of similar width if you can.
Is US size 3 the smallest ring size?
Size 3 is the start of this reference table. Offered sizes vary by design and maker. Check what is available on the individual product page and, for an unusual fit, ask the maker what it can produce.
Check Fit After the Lookup
Take this measurement as a starting point if you are sizing a broad band or stack. Use the fit guide for wide bands, knuckles, and stacks and then check available ring sizes on the design you are considering.


